Jump cuts: what they are, and a measured example
A jump cut is a cut that makes the subject seem to jump, because the picture before and after the cut is almost the same. This page says when it helps and when it hurts, and shows what a real run of a cutting tool produced on our test clips.
What a jump cut is
A jump cut joins two pieces of the same shot, from nearly the same camera position, with a bit of time removed between them. The speaker's head or hands move a little between the last frame before the cut and the first frame after it. That small move is the jump.
In talking-head video, jump cuts usually come from removing pauses, fillers and retakes. Removing silence automatically makes a jump cut at every gap it removes.
When a jump cut helps
- You want to drop a pause or a retake and keep the speech going.
- You can hide the join. A small push-in on the piece after the cut changes the framing, so the cut reads as intended. Our micro-zoom recipe is on camera moves.
- The cut lands in a clean gap, not inside a word.
When a jump cut hurts
- The cut lands inside speech. In our test the stricter setting removed up to 1.71 seconds of time the official subtitles show someone talking, on one clip.
- The kept pieces are very short. The same run left a piece of 0.46 seconds between two cuts and removed a gap of 0.04 seconds, which show as visible jumps.
- The audio under the picture has a music bed or room noise. The tool then cuts at the wrong places or barely cuts at all.
We make no claim here about how viewers respond to jump cuts. We did not measure that.
Our measured example
We ran auto-editor 29.3.1 on three 60-second clips of film dialogue with music underneath, once on its default setting and once with the audio threshold at 8%. Each cut is a jump cut in the output. The table counts the pieces it kept.
| Setting | Clip | Kept pieces | Cuts | Seconds cut | Shortest piece between two cuts (s) |
|---|---|---|---|---|---|
| Default | tos_a | 2 | 1 | 1.33 | No piece between two cuts |
| Default | tos_b | 1 | 0 | 0 | No piece between two cuts |
| Default | tos_c | 1 | 0 | 0 | No piece between two cuts |
| Threshold 8% | tos_a | 4 | 3 | 2.08 | 2.13 |
| Threshold 8% | tos_b | 12 | 11 | 5.42 | 0.46 |
| Threshold 8% | tos_c | 3 | 2 | 0.71 | 2.16 |
The busiest run was the stricter setting on tos_b: 12 kept pieces, 11 cuts, 5.42 seconds removed, and a shortest piece of 0.46 seconds between two cuts. On the default setting two of the three clips were not cut at all, because the music keeps the sound level above the silence line.
Read the table as a warning about music beds. A clean talking-head recording would behave differently, and we have not tested one yet.
How to make jump cuts
To cut silence automatically, run auto-editor. These are the two commands we ran.
auto-editor clip.mp4 -o out.mp4auto-editor clip.mp4 --edit audio:threshold=8% -o out.mp4Then check every cut by eye. Our remove silence tool page covers the same job, and the full run is on our auto-editor test. For the wider job of editing a talking head, see the talking-head workflow hub.
Method and limits
- Three 60-second clips (180 seconds in all) from one film are a narrow test.
- Kept pieces and cuts are read from the cut list auto-editor exported. The shortest piece counts only ranges with a cut on both sides; the pieces at the very start and end of a clip are left out, because they do not show as a jump. Speech cut is approximate, because it uses the timing of the film's official subtitles as a map of speech.
- We did not measure how viewers respond to jump cuts, or how long editing by hand takes.
- Footage: Tears of Steel, (CC) Blender Foundation, mango.blender.org, used under CC-BY 3.0. We do not publish the cut videos.
Page checked on Nov 4, 2026.